Roof Coating Calculator
Calculate how many gallons and 5 gallon pails of elastomeric roof coating you need for a flat or low-slope roof, plus reinforcing fabric rolls.
Add this calculator to your website — get the free widget
How to Calculate
Gallons = roof area × number of coats ÷ coverage per gallon per coat, plus waste. Most elastomeric acrylic coatings cover about 100 ft² per gallon per coat at a 10–12 mil dry film; two coats is the usual spec.
A 5 gallon pail is about 19 liters, which is the same pail sold in Mexico as a "cubeta". Mexican labels often list yield as roughly 1 liter per m² per coat, which is about 41 ft² per gallon and gives a thicker film.
Fabric is counted at about 1,000 ft² usable per roll (a 40 in × 324 ft roll, or a 1.1 × 100 m roll in Mexico, after overlaps). Most jobs only need it on seams, cracks, drains and around penetrations.
See our methodology for how every calculator on this site is built.
Worked Example: A 40 × 25 ft Flat Roof
A flat roof over an addition, 40 ft by 25 ft, getting two coats of elastomeric acrylic at the label rate of 100 ft² per gallon per coat. We'll reinforce the seams and drains and add 10% for waste.
- Roof area: 40 × 25 = 1,000 ft²
- Coating for two coats: 1,000 × 2 ÷ 100 = 20 gal
- With 10% waste: 20 × 1.10 = 22 gal
- Pails: 22 ÷ 5 = 4.4, so 5 pails of 5 gal
- Fabric over about 15% of the roof: 150 ft², so 1 roll
The leftover from the fifth pail is not wasted. It goes into the fabric, which soaks up coating like a sponge, and onto curbs, parapets and the flashing around vents, which you didn't count in the flat area.
Coverage by Product Type
Coverage depends on the film thickness the manufacturer specifies, not on how far you can stretch a gallon. Thin coats look fine on day one and fail early.
| Product | Typical rate per coat | Gallons per 100 ft², 2 coats |
|---|---|---|
| Elastomeric acrylic | 100 ft²/gal | 2.0 |
| Heavy-build acrylic or fibered | 75 ft²/gal | 2.7 |
| Mexican label rate, 1 L/m² | about 41 ft²/gal | 4.9 |
| Silicone (often one coat) | 65–100 ft²/gal | 1.0–1.5 |
The 1 L/m² rate on many Mexican pails builds a much thicker film, which is how those products earn their 5 and 10 year ratings. Follow the rate on whatever you're buying.
Where Roof Coating Jobs Go Wrong
Dirty roofs
Coating sticks to whatever is on the surface. If that's dust, chalk and algae, the coating peels with it. Pressure wash, let it dry a full day, and prime if the label calls for it.
Ponding water
Most acrylics are not rated for water that stands more than 48 hours. Low spots need to be built up or drained, or switch to a silicone product rated for ponding.
Rushing the second coat
Put the second coat on too soon and you trap water under it. Wait until the first is dry to the touch, usually 4 to 24 hours depending on heat and humidity.
Practical Tips
- Seal seams, cracks and penetrations with fabric and a base coat first, then coat the field.
- Roll the second coat at right angles to the first.
- Check the forecast. No rain for 24 hours and no dew at night.
- Use a wet-mil gauge on the first few pails to check your thickness.
Rough Cost
Elastomeric acrylic roof coating runs about $100 to $250 per 5 gallon pail in the US, silicone $250 to $400. The 1,000 ft² roof above takes about $500 to $1,250 in material. Contractors typically charge $2 to $4 per square foot installed, including cleaning and seam repair.
Sources
Frequently Asked Questions
How many gallons of roof coating per square?
About 1 gallon per coat for every 100 ft², so 2 gallons per square for a two-coat job. Heavier specs run 1.5 gallons per coat.
How many coats of elastomeric roof coating?
Two. The second coat goes on at right angles to the first once it is dry to the touch, which covers pinholes and thin spots.
Can I apply roof coating over an old coating?
Yes, if the old coat is well bonded. Pressure wash, scrape anything loose, and test a small patch for adhesion first.
When is it too cold or wet to coat a roof?
Most acrylics need 50°F and rising, a dry deck, and no rain for 24 hours. Morning dew on a cold night can wash out a fresh coat.
Does roof coating stop leaks?
It seals hairline cracks and worn surfaces. Open seams, blisters and wet insulation need repair first, or the coating just hides the problem.