Mortar & Concrete Mix Calculator
Work out how much cement, sand, gravel and water to mix by hand for concrete (1:2:3, 1:2:4) or mortar (1:3, 1:4, 1:5), in sacks, cubic yards and gallons.
Add this calculator to your website — get the free widget
How to Calculate
Wet volume = length × width × thickness, plus waste. Dry materials shrink when water is added and the sand fills the gaps in the gravel, so the dry volume is about 1.54 × the wet volume for concrete and 1.33 × for mortar.
Split the dry volume by the ratio. In a 1:2:3 mix there are 6 parts: cement gets 1/6, sand 2/6, gravel 3/6. Cement weighs about 94 lb per ft³, which is why a US sack of portland cement is 94 lb (1 ft³).
Water is a rough guide: about 0.5 lb of water per lb of cement for concrete and 0.7 for mortar, which comes to roughly 5.6 and 7.9 gallons per sack. Add it a little at a time; sand that sat in the rain already carries a lot.
See our methodology for how every calculator on this site is built.
Worked Example: A 12 × 10 ft Slab Mixed On Site
A 12 ft by 10 ft pad, 4 inches thick, mixed by hand or in a small drum mixer at 1:2:3 cement, sand and gravel by volume. We'll add 5% for waste.
- Wet volume: 12 × 10 × (4 ÷ 12) = 40 ft³, plus 5% = 42 ft³ (1.56 yd³)
- Dry volume: 42 × 1.54 = 64.7 ft³
- One part: 64.7 ÷ 6 = 10.8 ft³
- Cement: 10.8 ft³ × 94 lb = 1,013 lb, or 11 sacks of 94 lb
- Sand: 2 × 10.8 = 21.6 ft³ = 0.80 yd³
- Gravel: 3 × 10.8 = 32.3 ft³ = 1.20 yd³
- Water: 1,013 × 0.5 ÷ 8.34 = about 61 gal
Eleven sacks and two yards of aggregate is a long day for two people with a mixer. That's about the size where ready-mix starts to make sense, even with a short-load fee.
Switch the same pad to 1:2:4 and the cement drops to about 10 sacks, while the gravel goes up. That saves a little money, but it's a weaker mix, and a driveway apron or a step that takes a beating is not the place to cut it. For mortar the gravel line disappears and the sand line grows: a 1:4 mix for a 10 ft × 6 in × 8 ft block wall core fill is a different calculation, so measure what you are actually filling or plastering.
Common Mixes and What They're For
| Mix | Parts | Typical use | Sacks per yd³ (approx.) |
|---|---|---|---|
| Concrete 1:2:3 | 6 | Slabs, steps, posts, columns | 6.9 |
| Concrete 1:2:4 | 7 | Footings, mass fill, lean base | 5.9 |
| Mortar 1:3 | 4 | Exterior plaster, wet areas | 9.0 |
| Mortar 1:4 | 5 | Block and brick laying | 7.2 |
| Mortar 1:5 | 6 | Interior plaster | 6.0 |
Mortar volume here means mortar you place, for example a screed or a plaster coat. For block walls it's easier to use a brick or block calculator, which counts joints per unit.
Why the Dry Factor Matters
Mix one bucket of cement, two of sand and three of gravel and you won't get six buckets of concrete. You'll get about four. The sand fills the voids between the stones, the cement fills the voids in the sand, and water settles the whole batch. The 1.54 factor for concrete and 1.33 for mortar are standard field allowances for that shrinkage plus a little loss.
Practical Tips
- Measure by bucket, not by shovel. Shovels vary too much from one person to the next.
- Use clean, washed sand. Clay and silt weaken the mix and cause cracking.
- Add water slowly. A concrete that holds its shape in a squeezed handful is about right.
- Keep the finished work damp for at least three days.
Rough Cost
A 94 lb sack of portland cement usually costs $14 to $20 in the US. Bulk sand and gravel run roughly $30 to $60 per cubic yard plus delivery. The pad above comes to about $210 to $340 in materials, against roughly $230 to $350 for 1.75 yd³ of ready-mix before delivery fees.
Sources
Frequently Asked Questions
What is the best concrete mix ratio for a slab?
1:2:3 by volume gives a stronger mix for slabs, steps and posts. 1:2:4 uses less cement and is fine for footings, fill and non-structural pads.
What ratio is used for mortar?
1:3 for strong mortar and plaster in wet areas, 1:4 for general block and brick work, 1:5 for interior plaster and low-stress walls.
Why is the dry volume bigger than the wet volume?
The fine material fills voids between the coarse, and water settles everything. Without the 1.54 factor you would run out of material about a third of the way through.
How much water per sack of cement?
About 5 to 6 gallons per 94 lb sack for concrete. More water makes it easier to place but weaker and more likely to crack.
Should I use bagged premix instead?
For under about half a yard, premix bags save hassle. For larger jobs, mixing from bulk sand, gravel and cement sacks costs much less.